An ABS light on the dash means the anti lock braking system has found a fault. Your normal brakes usually still work, but the anti lock function may not. This guide explains six common reasons the ABS light comes on and what to check first. If a control module is the culprit, our brake parts department lists ABS modules for several trucks and SUVs.

Table of Contents
What the ABS light tells you
The ABS light comes on when the system self test finds a fault. The car should still stop, but without the anti lock help on slippery roads. Treat a steady ABS light as a reason to inspect the system soon.
A faulty wheel speed sensor
Each wheel has a sensor that reports speed to the ABS unit. Dirt, damage or a failed sensor sends a bad signal and sets the ABS light. It is one of the most common causes and often the cheapest to fix.
Low brake fluid
The system watches fluid level. A low reservoir can trigger the ABS light as well as the brake warning light. Check the level, and look for a leak if it keeps dropping.
A blown fuse or wiring fault
A blown ABS fuse or a damaged wire stops the unit getting power. Check the fuse box first because it costs almost nothing to test.
A failed ABS control module
The control module is the brain of the system. When it fails, the ABS light stays on and the system may not work at all. We list Dorman parts such as the Dorman ABS control module for the 2000 to 2002 Chevrolet Suburban 1500. These are the dearest brake parts in the range, so confirm the diagnosis first.
Worn tone rings or hub parts
The sensor reads a toothed ring at the wheel. If it is cracked or clogged, the signal drops out. A scan tool that reads ABS codes will point to the wheel involved.
What to do next
Read the codes with a scan tool, fix the cheapest causes first, and confirm the exact vehicle and years before you buy a module. Contact us with your details if you want a fitment check.
How to diagnose an ABS light step by step
Start the car and watch whether the ABS light stays on. Check the brake fluid level, then look at the ABS fuse. Next, read the codes with a scan tool that supports ABS, because a basic engine code reader may not show them. The code usually names a wheel, which turns a vague ABS light into a specific sensor or ring to inspect. Only then decide whether the control module is likely at fault.
Is it safe to drive with the ABS light on
Normally the brakes still work, but the anti lock function does not, so the wheels can lock in a panic stop. If the ABS light comes on with the red brake light, stop and have the system checked. For an ABS light alone, drive gently, leave extra stopping room and arrange a repair soon. Never ignore an ABS light that comes on with a soft pedal.
Parts price range and a checklist
ABS modules in our range sit at roughly $465 to $620, which makes them the dearest brake parts we list. Before you buy, check the vehicle, years and engine, confirm the codes, and rule out cheaper causes behind the ABS light. Delivery cost and time are shown at checkout. See the full brake parts department or contact us before you order.
Questions people ask about the ABS light
Will the warning light clear itself? Sometimes a fault is temporary, but a light that returns needs a proper check. Can a weak battery turn the warning light on? Low voltage can trigger it, so test the battery early. Does the warning light affect an inspection? Rules vary, so check the requirements where you live. Can I reset the light myself? A scan tool can clear codes, but if the fault is still there the light will return.
Keeping the anti lock system healthy
Keep brake fluid fresh, because moisture damages the ABS unit over time. Clean the wheel sensors when you service the brakes, and take care not to damage the wiring. If you drive through deep water or salt often, rinse the wheel areas regularly. After any repair near the wheels, check that connectors are fully pushed in, because a loose plug is a common reason for the warning light to return.
Step by step: a simple ABS check
Switch the ignition on and confirm the warning light behaviour. Check the brake fluid, then the fuse. Inspect each wheel sensor wire for damage and the connector for corrosion. Read the stored codes, note which wheel they name and compare the sensor reading against the others. If the readings differ, clean or replace that sensor. Clear the codes, take a short drive and see if the light returns. A light that comes straight back points to the control module or wiring.
Next step
Browse the parts mentioned in this guide, compare listings for your vehicle and check the years before you order. For more background, see NHTSA recalls lookup.